International Interdeck 1L (Pick-up only)

*This is a dangerous goods item and can only be picked up from Oddies Marine in Picton at this stage.

An excellent, easy to apply slip-resistant finish for decks.

Interdeck is a single pack slip resistant coating whose tough polyurethane resins give great protection against wear and tear. A durable slip-resistant finisih giving sure-footed and hard wearing protection to all deck surface. Resists sun and saltwater spray. Interdeck contains a fine aggregate that will apply easily on all substrates.

Colours match Brightside shades. Above water use.

PRODUCT DESCRIPTION:
Interdeck provides an excellent slip resistant finish. It contains a fine aggregate and will apply easily on all substrates.
* Low sheen finish prevents dazzling reflected sunlight off decks
* Easy application
* Available in a range of colours
The tough polyurethane resin protects decks against everyday wear and tear. Enamel.

PRODUCT INFORMATION:
Finish- Low sheen
Specific Gravity- 1.4
Volume Solids- 54%
Typical Shelf Life- 2 yrs
VOC (As Supplied)- 357 g/lt

Drying-Walkon/Touch Dry:

5ºC: 4 days/5 hours

15ºC: 3 days/4 hours

23ºC: 2 days/3 hours

35ºC: 1 day/2 hours

Overcoating Substrate Temperature -Overcoated by Interdeck:
5ºC: Min 24hrs/Max 4days

15ºC: Min 20hrs/Max 3days

23ºC: Min 16hrs/Max 2days

35ºC:  Min 12hrs/Max 1day

APPLICATION AND USE:
Preparation-

Sound Painted Surfaces: Thoroughly degrease with International Surface Prep then rinse with fresh water. Allow to dry. Abrade thoroughly with 280-320 grade paper as a minimum. Apply one coat of Pre-Kote all over followed by 1-2 coats of Interdeck.
Unsound Painted Surfaces: Remove all unsound coatings and treat as for new surfaces.

NEW SURFACES: Surface preparation is critical. All preparation for bare substrates is covered on the appropriate primer datasheet.

TIMBER: Apply Yacht Primer.

STEEL: Prime with Yacht Primer or Interprotect.

ALUMINIUM: Prime with Etch Primer followed by either Yacht Primer or Interprotect.

GRP: Never painted but in new or excellent condition: No priming necessary. Thoroughly degrease with International Surface Prep then rinse with fresh water. Allow to dry. Abrade with 180-220 grade paper.
Never painted and in poor condition: Thoroughly degrease with International Surface Prep then rinse with fresh water. Allow to dry. Abrade with 180-220 grade paper. Apply 1-2 coats of Yacht Primer to seal surface before applying undercoat.

ALL SUBSTRATES: Use Pre-Kote undercoat.

Method:

Sand the undercoat with 180-220 grade wet or dry paper. Remove dust with a dust wipe. Apply 1-2 coats.

Hints:

Mixing- Stir well before use.
Thinner- YTA800 International Enamel Thinners #1.
Cleaner- YTA800 International Enamel Thinners #1.
Ventilation and Humidity Control- Apply in dry, well ventilated conditions.
Other: For best results either stipple by brush or use a mohair roller.

Some Important Points:

Product temperature should be minimum 10°C and maximum 30°C. Ambient temperature should be minimum 5°C/40°F and maximum 35°C/95°F. Substrate temperature should be minimum 5°C/40°F and maximum 35°C/95°F.

Compatibility/Substrates:

Suitable for all substrates and filled surfaces. Not suitable for permanently immersed surfaces. Do not clean with highly alkaline cleaners.

Number of Coats 1-2

Coverage (Theoretical) - 9.50 (m²/lt)

Recommended DFT- 50 microns dry

Recommended WFT- 93 microns wet

Application Methods- Brush, Roller